The Basics of Plumbing Skills for Bathtub Installation
The Basics of Plumbing Skills for Bathtub Installation
Blog Article
We've found this great article relating to A Step-by-Step Guide to Installing a Bathtub down the page on the internet and think it made sense to discuss it with you on this page.
Mounting a tub isn't precisely brain surgery, yet it does call for solid plumbing, carpentry, as well as often, tiling skills. Replacing an old bathtub with a new one is additionally a reasonably hard project. If the old tub is easily easily accessible, the task can relocate quickly; if you need to open up a wall surface to get rid of the old tub and place the brand-new tub, the task is a lot harder. In either case, the job is within a house handyman's abilities, although you will need an assistant to move out the old tub and also set in the brand-new one. Make certain you have actually certified yourself for the work as well as are comfortable attempting it. Rather than employing a professional to take control of a halfway-completed job, it is far better to take into consideration employing one prior to you begin. Opportunities are you might require a specialist plumber to make tube connections.
This write-up will certainly help you install a new bath tub in your shower room if you have actually currently gotten a new tub as well as don't need to alter the plan of your previous water pipelines.
Your devices and product list ought to consist of the following:
Planning for the Installment
First of all, the supporting structure supplied with the bathroom needs to be fitted (if needed) according to the manufacturer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to make sure that if the faucet includes a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bath, it is additionally reasonable to fit a supporting plate under the faucets system to stop pressure on the bath tub.
Fit the flexible tap ports to the bottom of both faucets making use of 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet through the hole in the bath. Use the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you use every one of the provided washers.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath should now prepare to be fitted in its last position.
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your installment, after that the first thing you should do is disconnect the water supply. After doing so, switch on the faucets to drain pipes any water staying in the system. The process of eliminating the existing faucets can be rather bothersome as a result of the restricted gain access to that is typically the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the faucets. Have a cloth prepared for the continuing to be water that will come from the pipelines. When the supply pipes have actually been removed, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the single taps from transforming throughout this process. Once the taps have been eliminated, the holes in the bath/basin will have to be cleaned of any type of old sealing substance.
Prior to proceeding to fit the new taps, contrast the pipeline connections on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Mounting the Bathtub
Utilizing both wooden boards under its feet, place the bathtub in the required position. The wooden boards are practical in equally spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto 4 tiny factors.
The next goal is to ensure that the bath tub is leveled all round. This can be attained by inspecting the spirit level and adjusting the feet on the bath tub up until the spirit level checks out degree.
To install faucets, fit the bottom of the outermost flexible faucet port to the ideal supply pipeline by making a compression sign up with; then do the very same for the other tap.
Activate the water supply as well as examine all joints as well as new pipework for leakages as well as tighten them if required. Load the tub as well as also inspect the overflow outlet and the typical outlet for leaks.
Ultimately, take care of the bath paneling as described in the supplier's instruction manual. Tiling as well as sealing around the bath tub must wait until the bath tub has actually been utilized a minimum of once as this will certainly settle it into its last setting.
Suitable New Taps
If the tails of the new faucets are plastic, then you will require a plastic adapter to prevent damage to the string. One end of the connector fits on the plastic tail of the faucet and the other end supplies a link to the existent supply pipes.
If you require to fit a monobloc, after that you will call for decreasing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, position the tap in the installing opening in the bath/basin making sure that the washing machines are in area between the faucet as well as the sink. Protect the tap in place with the supplier given backnut. As soon as the faucet is safely in position, the supply pipes can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with normal tap connectors. The former kind needs to be linked to the tap finishes first, tightening up only by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the location where the bath satisfies the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is important as the installation can move enough to fracture a rigid seal, causing the water to pass through the wall between the bath and the tiling, bring about problems with moisture and possible leakages to the ceiling listed below.
You can select from a range of coloured sealants to blend in your fixtures as well as fittings. They are sold in tubes as well as cartridges, as well as are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with spins of soaked paper or soft rope. Keep in mind to always fill up the tub with water before securing, to enable the activity experienced when the tub remains in use. The sealer can split fairly very early if you do not consider this motion prior to securing.
Additionally, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily available on the marketplace. It is a good idea to fit the tiles making use of water-resistant or water-proof adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm certainly very serious about How to Install a Bathtub Yourself and I hope you liked the new article. Remember to take a moment to promote this write-up if you enjoyed reading it. Thanks a lot for your time spent reading it.
For fast relief, call! Report this page